Difference between revisions of "Select Station"

From meteobridge
Jump to: navigation, search
Line 13: Line 13:
  
 
====<font color="red">Limitation on USB 1.x Stations</font>==== <!--T:4-->
 
====<font color="red">Limitation on USB 1.x Stations</font>==== <!--T:4-->
Please be aware that Meteobridge client hardware from TP-Link (TL-MR3020 and TL-WR703N) is not able to run old USB 1.x devices directly, but needs a small cheap, unpowered external USB 2.0 hub in between, which translates USB 1.x from your weather station to USB 2.0. Following weather stations are impacted by this. Please check list of supported stations [http://www.meteobridge.com/wiki/index.php/Stations here], to learn in which situation you ned a USB 2.0 hub inbetween. As USB 2.0 hubs are available all around and do just cost a few dollars, this should be a no brainer.
+
Please be aware that Meteobridge client hardware from TP-Link (TL-MR3020 and TL-WR703N) is not able to run old USB 1.x devices directly, but needs a small cheap, unpowered external USB 2.0 hub in between, which translates USB 1.x from your weather station to USB 2.0. Please check list of supported stations [http://www.meteobridge.com/wiki/index.php/Stations here], to learn in which situation you ned a USB 2.0 hub inbetween. As USB 2.0 hubs are available all around and do just cost a few dollars, this should be a no brainer.
  
 
==Station selection== <!--T:5-->
 
==Station selection== <!--T:5-->

Revision as of 18:45, 23 April 2013

<languages /><translate>
This page allows to specify the station you have connected via USB to your meteobridge. Selection is very simple, just click on the radio button that matches your station type.

Page1.png

Automatic Station Identification

Meteobridge does not provide a complete automatic recognition of the station being connected, but it can do some checks, which might help you selecting the right station.

  • A green mark indicates that meteobridge's USB port has a device connected that identifies itself as being a weather station of that certain type. In case of Oregon stations WMR-88, WMR-100, and WMR200 meteobridge cannot decide which one is connected, but it can tell you if one of these is connected, so all of these are marked green when that type of station is connected.
  • A red mark indicates that the corresponding station is not connected for sure. Nevertheless, you can select it, which might be usefull when you do the setup without the station connected.
  • No mark indicates that there is a RS232-USB converter connected, so one of the serial connected weather stations might be there, but meteobridge cannot say for sure if there is a station behind the converter and what type of station might be there.

Limitation on USB 1.x Stations

Please be aware that Meteobridge client hardware from TP-Link (TL-MR3020 and TL-WR703N) is not able to run old USB 1.x devices directly, but needs a small cheap, unpowered external USB 2.0 hub in between, which translates USB 1.x from your weather station to USB 2.0. Please check list of supported stations here, to learn in which situation you ned a USB 2.0 hub inbetween. As USB 2.0 hubs are available all around and do just cost a few dollars, this should be a no brainer.

Station selection

Meteobridge supports the most popular weather stations in the market. Stations with a serial RS232 interface can be connected by a cheap RS232-USB converter. Converters with PL230x, CP210x and FTDI chipsets are supported by Meteobridge.

Davis Vantage Pro and Vue stations can be equipped with an IP-based Logger called WLIP. If you have one of these, you can enter IP and port (separated by a colon) in the "WLIP" input field (example: "192.168.1.222:10001"). This will tell Meteobridge to connect this station not via USB but via your LAN/WLAN (in the example on IP 192.168.1.222 at port 10001).

Station Altitude

It is important that you specify the station altitude. Meteobridge uses altitude information to compute sealevel pressure used by weather networks. You can specify altitude in meters or feet, please set down-down box for selection of "meters" or "feet" accordingly.

Tolerated Data Age

Meteobridge needs to know how long a sensor value should be regarded valid. Standard is 10 minutes, it is not recommended to go below that value. If your weather station does have RF problems with certain sensors that only change slowly over time it might be a good move, to increase the value. When you don't know, stay with the default of 10 minutes.

Confirm Changes

When you press "Save" weather station selection is made permanent and data logger is restarted to adapt to the new settings. </translate>